What if there was an LE error on a Samsung washing machine

New generation washing machines are designed so that they themselves tell us about the malfunction. Imagine: you decided to wash the laundry, loaded it into the drum, set the desired program and suddenly found an impressive pool of water on the floor. And on the washing machine brand Samsung brought error LE, LE1, LEC or E9. If you understand the values ​​of these codes, you can understand the essence of the problem.

What to do if the display shows an error code

So, the error LE in the machines "Samsung" means the spontaneous discharge of water from the tank unit. There are several reasons for the occurrence of such a breakdown:

1. Drain hose installed incorrectly.
2. Disconnected hose to the sewer system.
3. Damage to the tank to drain the water (crack, weakening the fortifications of bolts).
4. Drain filter not fully closed.
5. Disconnection of the air tube, due to which water starts leaking in the spin mode.
6. Fault in water level sensor.
7. The work of the indicator itself is broken.

Decipher codes

Errors in the Samsung brand washing machine may be indicated differently, but signal the same problem - water leak from the tank. Depending on the model year of this brand, LE, LC, E9, LE1 codes may appear on the screen. The E9 cipher, for example, was used by the manufacturer in early models of washing machines, until about 2007.

The design of the machines provided for the presence of the pressure switch, or water level sensor. If the sensor 4 times in a row detects a drop in the water level below the established rate, then one of the listed error codes will appear on the display.

Procedure for fault detection

An error may appear on the indicator both at the beginning of the wash and during the rinsing or spinning process. To rectify the problem in time and return the washing machine to life, follow a number of the following steps.

1. Disconnect the machine from the electrical outlet by unplugging the power cord.Press the power button on the case of the washing machine.
2. Carefully inspect the drain hose - there should be no cracks or tears. Well check its position, integrity and connection to the sewer.
3. If the drain hose is in the wrong position, connect one end to the bottom of the machine, the other end up, attaching it with a special hook. Fastening the hose to the drain pipe must have good tightness and be located at a distance of at least 70 cm from the floor.
4. Consider a drain filter device. To open the lid, turn in the counterclockwise direction, close it - respectively, you need to move the lid clockwise. If the cap is firmly attached and closes the drain hole, then the problem is not in the filter.
5. When it is impossible to identify the fault with the naked eye, it is better to contact the after-sales service. It is likely that the breakdown lies in the inside of the car. For example, broke tubular electric heater (TEN)there was a crack in the tank, another part failed. Qualified specialists will examine the cause of the error and, if necessary, replace the failed part.

If the error code first occurred, unplug the machine for several minutes. Perhaps the reason lies in the failure control module, and to resume proper operation, you just need to restart the technique.

What else errors can be

Not only the LE code tells us about the violations associated with the self-draining of water. It happens that dirty water does not drain out of the tank at all. Then the display lights up code 5E. It, in turn, is associated with a blockage of the drain hose or filter, or with a malfunction of the drain pump. Conduct repair the drain pump do it yourself quite possible.

Error 5d also refers to the outflow of water, but this time with soap suds. The reason for the increased formation of foam may be the wrong choice of washing powder (for example, intended only for hand washing) or exceeding its volume by one cycle. There is no need to fight this problem: after some time the foam will settle itself and retire, and the washing process will start again. But for the future, remember that only special-purpose tools with appropriate markings are recommended for automatic machines.

Do not use hand-washing powder in any case: after all, they not only spoil the clothes, but also can cause damage inside the machine itself, and this is much more serious.

Conclusion

Remember that spontaneous discharge of water is a rather serious mistake of the machine. After all, you can easily flood the neighbors from the bottom, if you do not pay attention to the problem in time. Manufacturers of modern models of "Samsung" greatly facilitated our task by providing the presence of codes on the display. Knowing the decoding of a code, you can fix the damage yourself. Just approach the solution of the problem responsibly, weigh your strength: can you fix the failure yourself? If not, then it is better to seek help from professionals who will repair and give advice on how to avoid re-leakage of water in the future.