What to do if the washing machine does not turn on

What to do if one day, deciding to wash your clothes and connecting the washing machine to the network, you find that it does not work? Trying to understand the cause of the malfunction, it is necessary to establish how the technique reacts to switching on. In total, two problems can be identified: the device does not react at all, the display does not light up, the lights do not flash; The machine turned on, but none of the programs start. Next, we will try to figure out what caused the fault, why the washing machine does not turn on, and what should be done in this situation.

Possible reasons

If you find that your washing machine is Samsung, Indesit, Ardo or Atlant “does not respond” when turned on, do not rush to make serious manipulations with it. Perhaps one of the reasons lies in this list of problems:

1. The apartment has no electricity.
2. Damaged power cord.
3. No voltage in the outlet.
4. Damaged power button.
5. Interference filter malfunction.
6. Faulty control module.

The machine "does not respond" to your actions

Finding out why your assistant doesn’t turn on - the washing machine will not be superfluous, before you start looking for a problem in the unit itself, to check for electricity in the apartment. Perhaps the lights were turned off in the whole house, and you noticed it just now. Another possible source may beshort circuit, which resulted in the electrical brush knocked out traffic jams.

The reason why a washing machine does not start may bedamaged power cord. This may occur due to its constant excesses in the same place, or due to mechanical effects. Carefully inspect the cord to eliminate external defects. Use a multimeter to test the wire for a fault. If the problem is caused by a damaged cord, replace it.In extreme cases, fix the breakage by applying electrical tape. If your machine is connected to the network via an extension cord, make sure that it is in working condition. Turn on the device directly to the outlet, or test the extension cord on a different technique.

Sometimes it happens that the machine does not turn on due to a malfunction.in the outlet itself. Check its performance by connecting any other device.

In some washing machines, the power supply is displayed on the power button. It should check its working condition by applying a tester. To do this, disconnect the equipment from the network and ring the button in the “on” position. If the multimeter makes a sound, it means that the button is working. In its disconnected state, the device must be silent. If you do not replace the button when a defect is detected, the machine will not turn on.

Such companies as Ardo, Virpul, Samsung, complete their equipment with an interference filter, however, the Indesit washing machine and Atlant SMA are not an exception. FPS should eliminate the electron radiation coming from the home appliance and capable of affecting the performance of other nearby equipment. Interference filter malfunction may occur due to short circuit. As a result, the electrical circuit is broken and the washing machine equipped with FPS stops switching on.

To check the operating status of the device, you need to use a multimeter. First we call three wires at the input, then two at the output. Voltage must be present at both ends. In the case of its absence at the output, the FPS must be replaced, since it is faulty.

The last part to check is control module, which is a printed circuit board, it needs to be tested using a tester. If you find a problem, do not rush to start repairing it yourself, assess your strength. It is better to use the services of the service center.

The machine works, but the wash does not start

If your washing machine is turned on, but the wash could not be started, the reasons for this may be different.

All indicators are operational

Turning on the washing machine and choosing the washing mode, you discovered that it does not start, although before that the technician behaved as usual: all the indicators were lit, the audio greeting sounded. First of all, make sure that the hatch of the washing machine is tightly closed and nothing is stuck in its lumen.

After the start of the program, the door must close with a lock, otherwise the protective mechanisms of the equipment will not allow the tank to be filled with water.

If the door is not blocked, it is necessary to check the blocking device for the presence of voltage in it. If it is absent, although current is supplied, the part should be replaced.

Make sure the water enters the drum - listen. Complete silence indicates that the ingress of water is difficult.

Check whether you have chosen the wash program correctly. Perhaps you simultaneously pressed two or three buttons at once or not at all. Disconnect the machine from the network for a couple of minutes and, most likely, the failure will be eliminated.

Light indicators light up randomly

If all the indicators on the washing machine are randomly lit, the fault is faulty. The Bosch washing machine, as well as appliances from other companies (Indesit, Samsung, Hotpoint, Ariston), have a characteristic feature. Their wiring is often in contact with other parts, which affects its performance. Install a problem area with a multimeter and change it.

Blown capacitors that need replacing can emit themselves by flashing all the bulbs in a random mode, or by simultaneously lighting them.

Conclusion

Sometimes a washing machine for unknown reasons may fail at the very beginning of the process, even without starting to wash. There may be several reasons for this: from the banal inattention of the hostess to the failure of the control module. The information outlined above should help to understand the problem when problems arising in the technique interfere with its normal operation. It will tell you what to do in different situations and what to do if the washing machine does not turn on, the wash does not start, or all the indicators blink.