Why does water remain in the washing machine after washing?

Malfunctions of such an important household appliance as a washing machine can turn into a real disaster for a person. But you should not immediately fall into a panic, sound the alarm and turn to expensive services. Common situation: water left in the washing machine after washing. In most cases, the problem is easily solved with your own hands, which takes a total of several minutes. What should I do if the washing machine has ceased to drain water from the loading drum after washing?

Possible faults

If you notice that after the end of the algorithm of washing the machine did not start to drain, do not rush to call the master. First determine the volume of the remaining liquid.It is important to understand whether this is not the remainder of the drained water, or the total volume of waste and not removed liquid. The reason for this kind of problem can be:

• kink drain hose or blockage in it;
• the formation of a strong blockage in the drainage filter, as a result of which excess water remains;
• if during operation the machine made an unpleasant hum, and at the end of the work it did not drain the water, it means that the drain pump was broken;
• if the pump is serviceable, but the water is retained in the washing machine, most likely the matter is fluid level sensor.

Water removal and repairs

Before starting any preventive or repair procedures, you must disconnect the household appliance from the mains and shut off the water supply. After this, be sure to check if the slug passing through the back of the washing machine is bent. It should be in a normal position, without obstructing the flow of clean and waste water. Then you can proceed to the removal of the remaining liquid after work. Prepare a bucket, a small container and dry rags in advance.

You can also drain the water accumulated in the drum through drain hose. Disconnect it from the siphon and simply lower it into the prepared in advance basin. So you can verify the performance of the hose and check whether it is clogged.

The water leaving without any difficulties, serves as a signal of a serviceable hose, and after this procedure it can be returned to its place.

Hose blockage

If the problem is still a blockage, it must be eliminated. Disconnect the hose from the washing machine, then, using special brush and cable, thoroughly clean its internal walls from accumulated deposits. After completing the procedure, flush the hose with clean water and put it back in place.

Drainage filter plug

Drain the water through the hose, you can begin to diagnose the drain filter. As a rule, it is located in the lower compartment, directly behind the outer panel or a special plate. Removing the filter, unscrew it counterclockwise and pull it towards you. Having found a blockage, fix it with a brush and running water. After thorough cleaning, reinstall the drain filter. No debris or foreign bodies should remain on it.

Breakdown pump

If you didn’t find any faults in the filter, you’ll have to check the drain pump. The pump of various models of washing machines in installed in different places. On devices like Samsung and LG, I mount it closer to the bottom panel. The German counterparts will have to tinker with disassembling the dashboard and dismantling the hatch. Read about where the pump is located. here.

Pressure switch failure

In addition to those described above, the reason for the delayed water in the drum may be incorrect operation of the pressure switch. In this case, you will have to spend it diagnostics. A worn water level sensor may incorrectly alert the control processor. Because of this, some liquid may remain in the drum. Check the health of his work as follows:

• remove the top panel of the washing machine;
• get to the pressostat, as a rule, it is located in the upper compartment of the system;
• disconnect wiring and hoses leading to the sensor;
• check the tubes for blockages, cracks and kinks;
• check and clean the electrical contacts of the device;
• using a multimeter, examine the resistance of the pressure switch;
• If any malfunction occurs, replace the sensor with a new one.

Timely replacement of this part will help you to prevent serious damage in the future.

How to prevent damage

Referring to the statistics, you can see that the occurrence of breakdowns of the drain system occurs already in the second - third year of intensive use of the washing machine. This is most likely due to the use of substandard parts at assembly. In an attempt to save on production, companies buy parts from cheap materials, which ultimately provokes a malfunction.

Also incorrect service life may be shortened installation and connection to sewage. Exceeding the standard length several times increases the load on the system, leading to its wear. To avoid such problems, experts recommend that you strictly follow the instructions of the technical passport.

The occurrence of blockages can also be prevented by following fairly simple tips:

1. Check the pockets of things before loading them into the drum; remember, debris and small objects are not allowed into it.
2. Periodically clean the drain filter from the remaining debris and sediment.
3. Arrange sessions full cleaning machine. Experts advise to use citric acid or specialized detergents.

Summing up, we can say that the liquid that has lingered in the loading drum at the end of the washing algorithm is obvious fault signal. Do not delay with their elimination: it can lead to serious accidents. Do self-diagnostics or call competent repair service specialists. Take care of the timely removal of waste fluid from the tank to avoid unpleasant odors. No need to stop cleaning and checking the details of the system after a long period of flawless operation. The washing machine system needs regular maintenance, do not forget about it, and it will work like a clock.