Because of this, a washing machine can drain water badly.

There may be a lot of reasons why a washing machine doesn’t badly or doesn’t drain the water at all. However, the result is the impossibility of the device to carry out the next stage of washing. Such a malfunction occurs quite often, but you can even solve this problem yourself, without the need to call the appropriate wizard. But for this it is necessary to identify the reason, because of what the water does not merge.

Causes of bad plum

It is very important to understand why water is not pumped out of the washing unit. The cause of improper pumping can be:

1. Filter blockage. When washing, various small items left in the pockets of clothes can fall into it: fabric, pieces of paper, coins, etc. That is why the technique cannot properly drain. It is recommended to produce periodic filter cleaningso that washing things happen according to the rules.
2. Clogged drain hose. This is a very common cause of incomplete draining of water from the tank. Should be disconnected and clean the hose.
3. The pump is not functioning properly. This element of the washing unit consists of pipes, impeller, made of plastic, as well as an electric motor. The reasons for the failure of the pump (pump) can be threads and hair wound on the impeller shaft. For this reason, the discharge of water into the sewer can be completely blocked. If you find a similar blockage is necessary release the water from the washing machine yourselfby removing pollution. Read more about how to clean the pump. here. The same reason for the failure of the drain pump can be the failure of the impeller, the breakdown of the electric motor. This requires the replacement of the entire node, otherwise the washing machine will not be able to just function normally.
   

4. Malfunction control module. The burnt out elements of the microcircuits or a failure in the firmware of the module may make it inoperable, as a result of which the washing machine will not be able to pump out water. In this case, repair or replacement will help. programmer.
5. Incorrect hose installation. With long operation, the pump power is reduced. Such power, as a rule, is sufficient for pumping water when using a hose, the length of which is usually about 1.5 meters. In the case of using a longer hose, the drain pump will simply not completely drain the water. This happens when an already outdated equipment was installed in another place and significantly increased the length of the hose. How to organize the discharge of water, read in our article.
6. Wiring fault. Due to improper installation of the washing unit, excessive vibration may occur. As a result, there may be faults in the wiring, which will lead to failure of the function of normal pumping water. This problem can be solved only by resorting to the services of a specialist.

If the life of the washing machine is more than 7-8 years, andabout spin clothes it makes noise, the pump may have broken. Need to replace it.

Many modern washing machines are equipped with a scoreboard, which shows not only the mode of operation of the unit, but also error codes. Thanks to this indication, it is possible to more accurately identify the occurring breakdown.

Self pumping

There are situations where the automation is not able to ensure the normal pumping of water. If the washing machine does not cope with the drain function, then this action must be carried out. manual method.

Independent discharge of water is carried out according to the instructions:

1. Unscrew the filter, which is located in the lower part of the unit, having substituted in advance the water tank. After that, you should tilt the washing unit in the direction of the filtering device and wait for all the water to drain.
2. If it is impossible to drain the water through the filter device, it is necessary to clean the nozzle, which needs to be moved a little before the water starts to drain.
3. If the water is not pumped out for other reasons, the water will be drained using a normal hose. Lower it to the bottom of the tank, create a drain, and remove the unnecessary liquid.

Call master

It is sometimes impossible to repair all the breakdowns in which the washing machine cannot perform normal pumping of water. Automatic washing machines can pump out water badly because the nozzle, which inside the washing machine is connected to the drain pump, is clogged.In case of malfunction of the pump, electrical wiring, as well as failure of circuit elements and software modules, the MCA can not only badly drain the water, but also do not pump it out at all. If you do not have the skills of repair and technical knowledge in the field of washing machine, you should contact a highly qualified specialist.