Decoding and troubleshooting Multivarki Redmond

Efficiency of preparation and multifunctional abilities of Multicookers of the Redmond lineup are known to many housewives, therefore, products are in high demand. However, like all household appliances, such devices sometimes break down during operation or do not start cooking mode, because the display of the Redmond multicooker appears errors with the letter E.

Error codes

The most common technical problem is when an error appears on the display. E1 or E2, E3. This usually means that moisture got into the product, and in order not to burn out individual parts, the automation in this way warns the user that it is urgent to disconnect the product from the network.

All variants of Redmond multivarok errors with the E symbol are described in great detail in the attachedmanufacturer instructions for use, there may also be indicated and recommendations for their elimination.

Different instructions interpret error codes in slightly different ways:

1. For example, if the device issues an E1 error, this may mean not only moisture, but also heating element burnout.
2. When on the display the automatics gives an error E3, then in this case it is necessary either to dry the inside of the product directly under the bowl or check the tight closing the multicooker lid.
3. Error E2 may appear with a short closing top thermal sensorlocated in the lid of the product.
4. Sometimes a home appliance displays an E2 error when it appears break in the connecting wireso it is necessary to check with a multimeter or ohmmeter in any case. We will talk about elimination methods a bit later.

If the Redmond multicooker has an E4 error, then most likely it means that pressure sensor clogged, but there may be some kind of breakdown in the electronic board, here you have to check everything.

Error code E5 means that automatics worked overheating protection equipment.

For each case, it is necessary to conduct a thorough inspection of the multicooker,if you cannot, for various reasons, do it yourself, then go to a service center, where professionals will help you for a minimal price (from 1 thousand rubles).

Solve simple problems

Let's start with the simplest - if the error code E1, E2 appears on the display, then this means that there is moisture inside, dry products or there are malfunctions in mechanical thermal switch. Eliminate the causes as they are detected: if under the bowl you did not find moisture or grains of salt, sugar and cereals, then turn the product over and unscrew the fastening of the bottom cover.

In the center, directly under the cup, installed thermocouple. Do not confuse it with a temperature sensor: it is tubular and very fragile, so we work with maximum caution. Two wires fit the thermal switch, take a thin strip of emery paper No. 0, fold in half to clean both contacts at once.

Easily press the top plate from the side of the adjusting screw until it clicks - this is a signal that the contacts have opened, shove the sandpaper, release the plate so that the contacts will close and energetic, but without fanaticism movements clearing the terminals, troubleshooting.After that, install all the removed parts in place and connect the product to the network. If the error does not appear on the display, then you can congratulate you on a successful independent repair.

If an error E3 appeared on the display, then moisture accidentally got into the device under the bowl - it’s a living thing, you have to carefully add liquid, because it’s not an ordinary saucepan, but an electronic device. Solving the problem is quite simple: disconnect from the network, take out the bowl - if it is hot, then give it time to cool. Then we turn the product over and unscrew the bottom fastener, remove it so that there is free access both from below and above.

To quickly dry the inside of the multicooker, you can use a hair dryer at low temperatures: thermistors and similar sensors are very sensitive to high temperatures.

We eliminate errors E4 and E5

Multivarka gives error E5 - automatic protected the product from overheating. This can happen for different reasons, in each case it is necessary to understand without haste. Many users in this case ask a logical question: what to do when the Redmond multicooker gives the E5 error to the display? Manufacturers of domestic appliances introduced special software foreffective protection against overheating of the entire body and individual parts of the product.

When, when the multicooker is turned on, the temperature sensor located in the lid generates a strong heating signal, the device stops the heating process and gives an error. Sometimes the hostess in a hurry just forgot to put the bowl inside the appliance. In another case, such a code will produce a product if products are laid in the bowl, and no water has been added for their preparation.

Most often it will be enough to conduct a series of very simple manipulations:

• immediately turn off the product by clicking on the “start” symbol on the display;
• unplug the multicooker by unplugging the plug;
• open the top cover to lower the internal temperature;
• wait at least 20 minutes until the device cools down sufficiently.

We check whether you have added everything to the bowl for cooking, if you have already prepared soup or broth for borsch, then you need to top up with boiled water at room temperature. We turn on the mode again: if a similar error occurs again, then a trip to the nearest one is necessary. service centerwhere your assistant is diagnosed on special equipment and will answer all your questions.

Error E4 - to cope with such a problem you need some experience and skills in working with sandpaper, because clean the pressure sensor contacts. If after stripping the product does not turn on, then again you will have to contact the service center, without a qualified master with a special tool you cannot cope.

Pressure Sensor Diagnosis

The basis of proper operation

If users adhere to the basic rules of operation of the Redmond multicooker, then error codes will appear less frequently on the display.

1. After each cooking, be sure to wash the bowl thoroughly, then let it dry and only then insert it inside the product.
2. The bypass valve on the lid of the product should be constantly washed, removing scale, and not wipe with a clean cloth.
3. Before turning on the cooking mode, be sure to tight closure of the multicooker lid, so as not to provoke an automatics to issue an error code.
4. The product should stand on a perfectly flat and solid surface.
5. Include the wire from the device only in good outlets with grounding.

Before you start using the multicooker, carefully read the instructions: following all the recommendations will save you from frequent repairs, and preparing a varied menu for the whole family with the help of a multicooker will turn into an easy and relaxed hobby without any extraneous troubles.

Manual to the Multicooker Redmond

It should be noted that the model range of products under the name Redmond is represented by all price categories: there are simple budget multicookers and the same with software for 55 options of modes, there are prestigious models with a unique design, designed for gourmets. Despite the functional and external differences, these models differ high security, stable reliability and simple control.

Manufacturers have thought about recipes - not only a guide for use is attached to each multicooker, but also a brochure with a minimum of 100 recipes.

The most reliable multicookers in 2018

Multicooker REDMOND SkyKitchen FM41S