Why AEG Dryer Shows Error Codes

Drying units from the German company AEG are of high quality, exceptional reliability, but they sometimes fail during operation. What needs to be done if the AEG drying machine produces certain error codes? Consider the malfunctions that you can try to fix on your own and difficult cases when you can not do without a master.

Content

1 Main malfunctions
2 When you can not do without a specialist

Main malfunctions

AEG drying machines (AEG) are premium-class appliances, so smart products independently analyze problems that occur and give an error code to the display. Any damage to the product at the factory during manufacture is assigned personal unique codeTherefore, when the error appears on the device screen, professionals already know what needs to be done in order for the product functionality to be restored.

Machines for drying clothes are divided into three main classes: basic, comfort and extra; in the latter, all the latest advanced technologies are used.

AEG drying machine

Trouble table that you can fix yourself

Type of fault	Causes of	Elimination methods
The unit does not turn on	The equipment is not connected. Blown fuse. The door of loading is not closed. By mistake, the Start-Pause button is pressed.	To plug. Replace fuse. Close tightly. Press again.
Poor drying	The wrong program is selected. One of the filters is clogged. Loaded too much laundry. Ventilation holes closed. There is sediment inside the drum.	Choose a more powerful drying mode. Clean the filters from foreign particles. Observe the recommended machine load values. Check whether the ventilation grilles at the bottom of the unit are open. Thoroughly clean the drum stiffeners.
The loading door does not open	Filters installed incorrectly.	Install correctly or snap the lid on the coarse filter.
When you press any key, an error appears on the display.	The protection has worked - after the start of the process, the mode cannot be changed.	Set the program controller to Off, set the mode again.
No drum light	The regulator is set to off. or a light bulb has burned out.	Install on any drying program or replace the light bulb.
The process is interrupted, the LEDs blink, the technician says - you need to drain the water from the condensate collection tank.	The condensate collection tank is full.	Drain the tank and press Start-Pause again.
Drying cycle is interrupted	Little laundry is loaded, or it is too dry for this cycle.	Choose a more powerful mode.
The drying process lasts longer than 5 hours.	Clogged filters. Loaded a lot of linen. Lingerie badly pressed. The high temperature in the room and the compressor turned off to avoid overloads.	Clear filters. Reduce loading. Re-press underwear in a centrifuge. The operation of the protection automation is not a malfunction. Air the room to lower the temperature.

The dryers manufactured by Electrolux under the AEG brand are much more reliable and have the highest quality compared to their competitors - they spend much less electricity on a work cycle,possess expanded functionality, carefully dry linen from any grade of fabric.

When you can not do without a specialist

The AEG dryer requires a rather delicate relationship with itself; often this household appliances suffer from power dropswhich occur in any region of Russia, unfortunately, very often. The machine stops and an error appears on the display - code E51, which indicates that a malfunction has occurred in the electronic control system of the product.

In this case, you must immediately turn off the product by unplugging the plug, then, if such a device is available, check the voltage in the home network. Call the master from the service center to fix your non-participation in the malfunction, as a result of which the error was displayed on the machine screen. You may need to repair the electronic components of the product mechanism — when the voltage drops, the control modules, electronic sensors and other electronic components of the machine suffer.

To further household appliances brand AEG did not issue this code on the display, install a voltage regulator or a protective shutdown device (RCD).

Residual current device

Sometimes car indicators start systematically blinkThis situation may arise for a variety of reasons.

The temperature regulator has failed - an urgent replacement is required.
The control board failed: you need to do a flashing or change the control unit.
The fan in the cooling system is broken - just change.
The drain filter is clogged - clean the filter from foreign particles.
The indicator “Full tank filling” is on - check the electrical contacts and the tank filling sensor.
Water does not drain due to a blocked hose - unscrew the connection and clean the hose.
The drain pump is broken - it needs to be replaced.

As can be seen from the registry, these serious malfunctions can be fixed only by trained specialists. Only two points out of seven can be done by a home master without any threat to the internal details of a gentle technique. clean the filter or drain hose.

Removing the pile filter of the drying machine

In the AEG dryers, the error code E50 is also sometimes encountered - a malfunction of the electric motor drive, however, according to experts, this happens extremely rarely.

That's all the main problems that may appear during the operation of the drying machine brand AEG. Carefully read the instructions for the product: there are all the specific nuances of a particular technique and possible codes with their full decoding. Remember, when the display shows a malfunction code - call the service center of the population, call the wizard for the diagnosis of household appliances, and do not try to resolve complex failures. By following our recommendations, you will extend the life of an expensive drying machine.