How to replace the gum on the refrigerator door

Often it is necessary to replace the gum on the refrigerator door. This type of breakdown is most common among older models.

Among the many breakdowns that lead to malfunction of the cooling technology, the most common is the malfunctioning of the seal.

Modern technology is not immune from the appearance of this problem. Basically, the essence of the trouble depends on improper installation on the factory conveyor or can be acquired with careless use in everyday life. Incorrect operation can cause any equipment to malfunction. At damage of an elastic band in the refrigerating chamber the temperature mode changes. To fix problems, the compressor runs at full capacity.

All this will lead to a malfunction of the motor of the refrigerator. The service center for the repair of household appliances will provide a huge bill for the repair.To avoid such trouble, you need to carefully monitor their refrigeration equipment.

Signs of improper operation of the seal

The main symptom of a malfunction of the seal is the loose fit of the door. If you doubt the correct operation of the gum, you can check it with a simple experiment. Need to take a strip of plain paper. Next, open the refrigerator door and put the paper on the compactor itself. After that we close it, leaving a small part outside.

With a good fit of the elastic to the refrigerator door, the paper cannot be pulled out. Accordingly, in poor performance, the paper will fall by itself without the use of physical force.

In addition to this experiment, there are many signs indicating a malfunction of the gum. The refrigerator runs continuously without shutdown. The entry of warm air masses through the gaps between the door and the chamber causes the compressor to maintain the required temperature inside the refrigerator.

The following phenomena are also possible:

1. Often a permanent job causes the motor to malfunction.
2. Insufficient cooling of the chamber space. In this case, the compressor works without stopping, which leads to a rapid process of food spoilage.
3. Constantly ice forms at the back of the wall. All this occurs as a result of the ingress of excess warm air.
4. The presence of condensate on the lower shelves.
5. Icing the freezer.
6. Formation of ice on the refrigerator door.
7. Insufficient temperature inside the chamber.

In the presence of these signs, you must contact the service center. It should be noted that the failure of the seal leads to rapid deterioration of products and a constant load on the compressor.

As a result of this, it can burn out due to overvoltage.

For each type of special design provides sealing tape. For Soviet technology, the tape did not have any differences.

Ways to restore the sealing gum at home

There are several proven ways to restore the gum yourself. Such work can be carried out on models that have expired warranty service. If the equipment is under warranty, then it is better to use the services of professionals.They quickly and efficiently perform all the necessary repair processes. To repair their own hands will need:

• hair dryer;
• hot water.

With a slight deformation, it is necessary to heat the problem area with a hair dryer. After that, you need to stretch it a bit.

When done correctly, the gum will take the opposite shape, which will ensure tight closing of the refrigerator door.

If you do not have a hairdryer, you can use hot water. The entire seal for a short period of time is placed in a container of boiling water. As a result, it will become more elastic, which will allow to correct problem areas.

Before proceeding with the repair, you need to carefully consider the options for attaching a rubber tape. The presence of screws will allow you to easily put it in its place.

It is necessary to fasten the sealing tape carefully so as not to damage the thread.

Glued gum requires special attention. After removing the damaged area, it is fixed on a special glue. You can buy it at the hardware store. For older models, it is quite difficult to find a suitable sealant, so you can use a universal one that contains the required number of tracks for tight fixation.Size may be several times larger than required. To do this, cut the desired piece with a knife. After that, it is mounted in place. The cut edges are smeared with the same adhesive for fastening.

In the presence of cracks on an elastic band, its complete replacement is necessary. An experienced professional is able to install a new compactor on modern equipment.

Professional help

In modern models of refrigerators sealing gum is hidden under the facing layer. There is no need to carry out self-repair, as with improper extraction of the material, you can spoil the look of the refrigerator door. The master quickly and efficiently conduct all the necessary manipulations. Replacement occurs in several stages:

1. Carefully removed the door.
2. The old sealing layer is removed. Along the entire perimeter, glue residues are cleaned.
3. When the place for installation is completely cleared, the master proceeds to install a new gum. New sealing tape will be much wider than the previous one. When this is achieved the maximum fit of the door.
4. After fixing the seal, the ends are glued together with a special glue. This is necessary in order to avoid the appearance of a gap between the door.
5. When the replacement is completed, the door is attached to its original place.

To care for the sealing rubber is quite simple. The main requirement is to keep it completely clean. How to wash the tracks? You can use warm water with detergent. After that, it is recommended to wipe with a cotton cloth. Silicone grease for seals will help to avoid drying out.