No Bosch water in the dishwasher

A variety of household appliances firmly occupies its niche in our house, today many housewives can no longer imagine their kitchen without silent automated assistants. No matter how reliable the Bosch equipment is, it also sometimes causes annoying failures: the moment came when the dishwasher did not get water.

Possible reasons

The German company Bosch produces very reliable household appliances and units, but even they are not insured against the occurrence of annoying problems - it is useless to complain that it was you who were sold a low-quality car. Most likely, water does not enter the car due to the reasons to which the producers of modern technology are not involved.

Experts have compiled a small list of the real causes of this failure:

1. There is no water entering the home plumbing system.
2. Shut off the water supply valve to the machine.
3. The filler hose is pinched or bend in place.
4. System Aquastop or Aqua-Control found a leak and blocked water intake.
5. Due to power surges in the network out of order solenoid valve water inlet - urgent replacement is required.
6. Loosely covered loading door or malfunction of the lock system.
7. Broken water level sensor in the tank, it gives incorrect information to the control module - as a result, the water inlet is stopped.
8. Net littered filter intake valve - the problem is solved pretty quickly, dismantled and washed.
9. Broken control module Bosch is the most serious problem of all, we need an urgent replacement.

You should not try to self-diagnose the machine in case of module breakdown - this may lead to the replacement of the unit with a new one before the deadline.

If you care assistant, then contact the professionals, everything will be done quickly and with a guarantee.

We understand in detail

If there is no water in the plumbing, then you need to be more careful and read the warnings on the bulletin board in front of your entrance - the housing office always warns residents about possible water outages due to maintenance work. Check whether open water tap in the dishwasher and the state of the filler hose is not difficult, however, as well as figured out whether the water pump or not.

Inlet valve

This item is absolutely on all brands and models of dishwashing machines. If it is faulty, water will not be drawn into the unit system, because the valve will not be able to open access to the inlet hose.

In the electric city network constantly occur voltage dropstherefore, an excessive voltage may be applied to the electromagnet winding, as a result of which it will burn out. If the winding is faulty, then the signal to the rod is not received, and the membrane of elastic rubber continues to block the entrance.

Repair such a product is not subject to - need to be changed. If you do not understand anything in the technical features of household appliances, it is better to invite the master from the service center.

Important! When self-replacing the solenoid inlet valve, it must be remembered that it must correspond to the brand and model number of the dishwasher.

Many home masters successfully and without problems cope with this replacement and save the family budget.

Loading door

While it is closed loosely - the machine will not work. It is necessary to click on it to the characteristic click, and if after that the water intake does not start, then the reason is in the blocking system. What to do in this case? First of all, do not panic, unplug the car and carefully examine all the elements of the door:

• deformation, even the smallest, sealing rubber always leads to a loose door closing;
• inspect Castle - when faults are detected, we change it or repair it;
• check the installation of baskets and containers - with incorrect installation they prevent the door from closing tightly;
• if the machine is not level, then the door may not close completely due to interference.

If the reason for a loose closure is a lock, then it can be replaced on its own, just buy a new lock for your model in advance. Lock Replacement Algorithm pretty simple:

1. Open the door and unscrew the mounting screws. Caution! The edges of the stainless interior coating are very sharp - do not cut your hands. Hold the top panel so that it does not fall out.
2. Disconnect the wiring terminal carefully.
3. Turn off the fasteners on the upper part and remove the lock in the direction.
4. We install a new one in place, we connect the terminal.
5. Insert the top panel in place and tighten the fasteners.

Replacement is made successfully, now you need to install a new latch so that all parts are new. How to do this, popularly explain the wizard from this video

Some household craftsmen, in order to save money, repair a failed lock, replacing the broken ones. plastic parts on more durable stainless metal. Nobody gives a guarantee that such a lock will work longer than the factory one, so why waste energy and reinvent the wheel?

Clean the filter

Quite often, the dishwasher does not collect water because of the blockage of the strainer, because the water is hard and its deposits clog the mesh of the filter element. We do everything on our own:

• close the tap, disconnect the filler hose from the machine;
• in the place of connection, there is a small filter inside - we take it out and rinse it under running water;
• if the grid is heavily clogged, then you can immerse it in citric acid for half an hour.

Then we put everything in its place and try to draw water, everything works - the repair is completed.

Control module

Problems with the management of all units and systems are rare, but sometimes a dishwasher even of such a reliable brand as Bosch does not get water due to electronics problems.

Modern home appliances are very smart and quickly respond to all changes. For example, the control module sends a signal to the pump to start discharging the waste water from the tank of the machine at the end of the cycle, but the incoming signal does not reach the drain pump due to problems. Does the machine buzz when turned on or does not respond to the Start button? It is necessary to call a specialist who will remove the module and in the laboratory will test in all parameters. If you can reflash, they will do it, but no - they will install a new one.

Table of approximate prices for services master service center

To this we must add the cost of spare parts, payment for the master of prestigious models starts from 2 thousand rubles.

We considered the main options for failure, which are encountered in practice, but sometimes even experienced masters are not able to immediately and accurately establish a diagnosis, but only after a comprehensive diagnosis of the machine in a special laboratory of the center.