Instructions for use of electronic cigarettes

Despite its simplicity, an electronic cigarette is a rather complicated product from a technical point of view. In addition, the gadget without proper care becomes capricious and may fail. When using a user, it is necessary to follow simple rules in order for the device to work effectively and durable.

Preparing an electronic cigarette for work

Beginners in the hover are primarily interested in the question of how to assemble and fill up their first purchased electronic cigarette. Consider this process on the example of several popular devices.

Eleaf iJust 2

If you purchased a basic package of an electronic cigarette, for example, Eleaf IJust 2, then when you open the package, you will see a battery, a clearomizer, a USB cable and a silicone ring (used to adjust the tightening force by blocking the air inlets), which describes in detail how to use the gadget.

To collect the vape, it is enough to screw the clergy to the battery pack.. The battery is charged via the USB port of a computer or laptop. Also available separately. network adapter to charge the battery from the network.

Many users of the device recommend first charging the battery for at least 8 hours, but before that completely discharge it.

To fill the device with liquid for soaring, do the following.

1. Unscrew the flask from the evaporator.
   
2. Take the evaporator in your hands and, gently turning it, soak the wick in liquid so that the slurry does not fall into the central hole.
   
3. Also drip liquid into side holes on the evaporator. The wick needs to be soaked with sludge very copiously: in this case it is better to pour than to underfill. If this is not done, then when the helix is ​​turned on, poorly soaked places on the wick will burn, and there will be a burning smell during soaring.
   

4. After the wick stops soaking up the liquid, pour it into the tank through the special holes, as shown in the following figure.
   

5. You can fill the tank completely, but it is not necessary to overfill the slurry.
   
6. After refilling, screw the flask to the evaporator.
   
7. Check for leaks.
   
8. Screw the clearomizer to the battery pack. Wait a couple of minutes until the liquid is well impregnated with the wick, after which the device will be ready to work.
   

In an improved model of the device iJust s is provided top dressing tank liquid: the upper part of the tank is removed and the required amount of liquid is poured, as shown in the following photo.

EVOD CE5

The basic package of the EVOD CE5 vape consists of the following components:

• EVOD 1100 mAh rechargeable battery;

• Clearomizer CE5;

• USB charging cable with connector suitable for EGO battery;

• 1 bottle (11 ml) with a liquid that you can choose to your taste.

The assembly of this vap is also very simple: twist the clearomizer and battery together. The battery charges from PC or laptopas mentioned above. Refueling this device is notable for its simplicity:

• first, unscrew the mouthpiece;

• after the mouthpiece is disconnected, it is necessary to take a bottle of liquid and pour it in such a way that it flows along the walls, bypassing the central hole;

• on average, the flask should be refilled to half or a bit more;

• after refueling, screw the mouthpiece to its original place and check that the liquid does not leak, after which the device can be used.

Joyetech eGo AIO

Joyetech eGo AIO starter kit includes the following components:

• vape assembly (with a mouthpiece), but without an evaporator;

• 2 replaceable BF 316SS stainless steel evaporators having a resistance of 0.6 Ohm;

• glass mouthpiece - 1 pc .;
• charging cable (micro USB);
• instructions for use.

Vape is going to be quite simple, as shown in the following figure.

But the device is already charging through micro USB portBuilt into the side of the unit.

The battery can be charged from a PC or from an AC adapter (purchased separately) with DC 5V output. After the battery is fully charged, the indicator located on the button goes out.

But the fact that you have collected all the components together is not enough to get the machine started. It is also necessary to pour liquid into it. This is done as follows:

1. Unscrew the base of the atomizer from the body of the device.
   
2. Remove the new evaporator (supplied) from the packaging.
   
3. Take the liquid and drip it into the hole to soak the wick well. Wetting should be very abundant and continue until the slurry is no longer absorbed.
   
4. On the back of the atomizer there are 2 holes, into which you should also drip the liquid, after which you need to remove the last remnants of the contact (pin). To do this, you can use a tissue or toilet paper.
   
5. After impregnation, attach the atomizer to the base.
   
6. Now you can refill the liquid in the e-cigarette flask itself. When refueling, pay attention to the label printed on the body of the vape, with the word “max”. Above this line you can not pour muck.
   
7. After filling the bulb, screw the base with the atomizer to it. Now the vape is fully operational.
   

How to turn on and off vap

Many newcomers, not having read the manual for the vape, trying to turn on the gadget, are frustrated and panic because their electronic cigarette does not turn on. This happens for the reason that in modern vapes there is protection against accidental activation, for example, in a pocket or bag. To unlock the vape and also enable it, you need to press the key 5 times within 3 seconds. If you want to turn off the machine after soaring, do the same procedure again.

If your e-cigarette does not have any buttons, it means that it is automatically activated when you tighten.

How to set up vape

The electronic cigarette in the form in which it was presented above does not need any special settings. Is that you can adjust the torque. Also, some of the more “advanced” vapers are trying to rewind the spiral themselves in order to, by changing its resistance, achieve other taste sensations while soaring.

For vapers, which are no longer satisfied with the standard electronic cigarette, there are so-called boxing fashionrepresenting the battery pack. The mod is equipped with an electronic control card and a small display. Thanks to the electronic stuffing, it is possible to more precisely adjust the vape to the needs of any bather. Therefore, the adjustment of the vap is to configure several parameters.

Power

This refers to the power that acts on the helix of the atomizer (steam generator).The larger the helix, the more power you can apply to it. But everything must be within reasonable limits, otherwise the heating element may burn out. Also directly depends on the chosen power battery discharge time: the higher it is, the faster the battery will sit down. It is recommended to set the average power value - from 15 to 20 watts.

If the power value is exceeded, the following negative points may appear.

1. The battery will quickly lose its charge.
2. There will be a strong heating of the body (sometimes it is difficult to hold the vape in the hands). In this case, the device must be turned off, and let it cool for a while.
3. maybe burning wick, and, as a result - a taste of burning during soaring.

Varivolt

The varivolt function allows you to manually change the voltage applied to the coil. However, the power will depend on the resistance of the heating element. Based on this, it turns out that the volume of inhaled vapor-air mixture depends on the voltage.

The principle of operation is quite simple: the higher the voltage value is set in the fashion, the more the heating of the spiral occurs, as a result of which the amount of steam increases and the aroma of the slurry opens more brightly. But if you exceed the voltage, it will burn the wick, and there will be a burning taste. Therefore, this parameter is selected by trial and error.

When changing the clearomizer (with a different resistance) again by the selection method, you will need to adjust the required voltage to achieve the required results.

Varivatt

Varivatt is the ability to adjust the power of the vap, if you change the resistance of the spiral, is improved version of varivolt. If your mode has a “varivat” function, then, as a rule, there is no need to manually adjust the voltage. This fact is explained by the fact that the voltage automatically adjusts to the resistance of the heating element. Thanks to the “varivatt” function, as in the Kangertech KBOX 120-200W mod box, a more precise adjustment of the vaping occurs, which allows the apparatus to achieve maximum results without failing the helix.

This feature gives the vaper the opportunity to comfortably use the device. It is enough to set the power that is comfortable for the bathers once and not to worry when changing clearomizers what is their omnity. The mod itself adjusts to the resistance of the clear and aligns the power to the previously set indicators.Therefore, whatever clears you put on, the power will not change, and the bather will always be able to observe a lot of smoke.

Thermocontrol

This feature is not available to all vapes. But if it is present in your gadget, then no need to configure it. Thermocontrol works in fully automatic mode and is only available when a nickel or titanium spiral is installed in your device. Only with such metals can the e-filling of the vape work.

Thermal control works as follows: if the temperature of the spiral reaches a critical level when steaming, then there is a decrease in power so that the heating element can cool down. For a vaper, this process usually occurs unnoticed.

Hover rules

Beginners who are accustomed to smoking traditional cigarettes often make mistakes while steaming. As a result, there may be side effects such as overheating of the device, leakage of liquid from the mouthpiece, the appearance of burning taste and others. But if you use the gadget, adhering to the following rules, then all these troubles can be avoided.

1. First tightening rule. It must be observed every time you are about to start steaming. It consists in the fact that the vaper must take the shortest possible tightening, so that the wick will begin to soak well with the liquid, as if lighting a cigarette before smoking.
2. First, it is recommended to take steam into your mouth, and then try to breathe into your lungs. Do not immediately deeply inhale, since the liquid for soaring can be quite strong. To get used to the pair, do from 10 to 12 short and, if possible, not deep puffs. That is how many puffs are required to smoke a regular cigarette.
3. Watch out for frequency and depth of puffs. If you make shallow but long puffs, this will allow the atomizer to generate saturated and dense steam. Avoid sudden breaths - this causes condensation to form, which can get into the battery contacts and cause a short circuit.
4. Do not hurry. The fact is that when tightening the helix is ​​heated, which, in contact with the wick, evaporates the liquid. It is necessary to cool down the spiral, and fill the wick with the liquid from the place from which it evaporated. If you do frequent tightening, the wick will burn, and the coil will overheat.
5. Keep the vape right. While hovering, the device must be held in such a way that it is slightly tilted. Due to this position, a more uniform flow of liquid to the evaporator occurs.
6. In some mechanical models of electronic cigarettes with a button (mehmod), in order to take a puff, you need to simultaneously press the button on the body of the gadget with a breath, and after releasing it, release it. Some vapers like to use mechmod, but most still prefer to turn on the steam automatically.

Security measures

While using the vape, you must follow the safety rules.

1. Do not allow the slurry to get into the eyes, mucous membranes and tongue. Moreover, you can not swallow it - it can cause poisoning.
2. Avoid contact with the device in direct sunlight, and do not keep the gadget in the room if it has high air temperature.
3. Take all measures to electronic cigarette did not fall into the hands of children.
4. Do not clean the gadget connected to the charger. Before preventive cleaning of the vape, it must be turned off (5-fold pressing the button) and disconnected from the charger if the device has been connected.
5. Do not put on vaping in a room with high humidity or outdoors in wet weather.
6. You can not soar behind the wheel. Remember, vaping is dangerous while driving, because the view is disturbed due to the thick cloud of steam.

Rings of smoke - it's just

Well, smoke, that is, soar, you have learned. What's next? Bored smokers have long figured out how to make this process more interesting. It consists in letting rings of smoke. Vapers have successfully adopted this experience and offer 3 basic ways to make this trick out of steam.

1. Type in a lot of steam in the lungs. Put your lips together as if you were saying the letter “O”. In this case, the tip of the tongue should be fixed in the center. Make a short and easy exhale, as if podkashlivaya. After a few workouts, you can make beautiful and smooth rings.
2. It is necessary to gain more steam, then roll up lips in the form of a tube and pull them forward a bit (no need for language help). Push the steam out of the lungs sharply and as often as possible. With this method, the first and the last rings are not obtained, but in general, the result is quite good.
3. This method of letting go rings is called “W” method. If you master it perfectly, you can make very beautiful and even rings of smoke. But first, learn how to pronounce the English letter “W” correctly. It sounds like “Ay” or closer to “Oh.” After working out the correct pronunciation, you can begin to learn to let the ringlets out of steam. Pour steam into your cheeks, then fold your lips, as if you are preparing to utter the sound “O”, and say the letter “W”, simultaneously releasing smoke from your mouth. When you pronounce an English letter, your lips should be as tight as possible. To change the size and clarity of the rings, you can change the diameter of the circumference of the lips.

Correctly release rings of steam like this video, can learn any vaper. But hovering fans went further and began to complicate this process. For example, you can release a cloud of mist, similar to a jellyfish, as in the following video. Neskuchnogo you soaring!