Algorithm of replacing wool in an electronic cigarette

How to change cotton wool in a vape yourself, you should know the novice user of this device. Experienced bathers with this, as a rule, are familiar. Replacing is a practical necessity, because with the regular use of an electronic cigarette the wick burns, an unpleasant taste appears in the mouth. Proper installation is of great importance: with an insufficient amount of material, the liquid flows slowly to the helix, carbon deposits are formed, with excess, the slurry begins to boil and burns the soaring cavity.

The first signs of the need for replacement, its frequency

The electronic cigarette is intended to replace the usual cigarette from tobacco. It is believed that it is less dangerous, but there is no evidence of this. Principle of soaring is as follows:

• the coil of the evaporative system of the atomizer is heated by electric current;
• the wick inside it is wetted with liquid;
• under the action of high temperature, the liquid begins to evaporate rapidly;
• combining with air, it forms steam, which the bather absorbs.

The presence of 2 parts is typical for vape:

• battery;
• atomizer.

The evaporator in turn can be of the following types:

• serviced, in which you can change the wick and helix during operation;
• maintenance-free, which is replaced with new wear.

Serviced option for electronic cigarettes is used much more often. There are such subtypes of the atom:

• clearomizer;
  

• dripka;
  

• bacomizer
  

By the method of blowing nozzles are divided into the following types:

• with side blowing;
• with blowing from below;
• combining both ways.

To properly fit the wick, you should consider the design features and the type of blowing.

The main signs that a new wool is needed are a change in the taste of the inhaled vapor (the appearance of burning notes) and a decrease in its quantity. The frequency of replacement depends on such factors:

• frequency of use of the device;
• on the quality of the wick material, the liquid used;
• compliance with the rules of operation.

On average, cotton wool with regular soaking is required replace once week. In most cases, it helps to get rid of unpleasant taste. If it remains, then install a new spiral. You must be guided by your own feelings.

Wick selection

Vata for vape should use the one that meets the following criteria:

• has an excellent ability to absorb water (hygroscopicity);
• has a fibrous structure without lumps, and when squeezed slightly crunches.

To determine hygroscopicity Selected materials to create a wick, you need to make small balls of them, then throw them into the water. Which ball will sink faster is the best option.

Manufacturers can use to make a wick:

• glass;
• wool;
• cotton;
• hemp;
• linen;
• wool;
• silk;
• wood (cellulose);
• hemp.

The best options are unbleached, non-sterile cotton wool, Japanese cotton, cellulose. The first, in comparison with the other two, burns out faster, which necessitates more frequent replacements. The most suitable is Japanese cotton.Sterile pharmaceutical cotton wool is not suitable for ES, because it has a strong influence on the taste of steam.

Serviced varieties steam generators need a wick that can equally well conduct and retain moisture. Each of the above materials has different characteristics in this regard. For example, flax, as quickly absorbs, and gives moisture. Cotton absorbs more slowly, but holds better. Therefore, it is recommended to use cotton wool for electronic cigarettes, consisting of different materials that will complement each other in their properties.

Remember: quality products do not contain short fibers, in its composition there is no dust.

Instructions for replacing the fleece

You can easily change the old wick to a new one. To do this, perform actions on the following general algorithm:

• take out unsuitable for use fleece;
• they clean the spiral of soot, burn it;
  
• check the coil heating uniformity;
  
• cut the required number of wick strips (1 per 1 helix) of the required size;
  
• remove excess fiber;
• give the cut strips the shape of a tube, twisting more thinly on one side;
• inserted into each spiral on the fleece;
  
• pruned tips on the parameters of the bath;
• put cotton wool around the spirals;
  
• moisten the coil and wick with a liquid for soaring.

Dripka feature with side blowing is the need to leave on the sides of the coil the same amount of filler, the tips of which are turned under the spiral. When using the device with the lower blowing care should be taken to ensure that the holes remain open after the wick has been laid. If they accidentally score, there will be practically no pair.

Change cotton is not difficult. Having spent several minutes, it will be possible to soar further without unpleasant taste sensations. The algorithm allows changing the wick mods from Eleaf (for example, on the Ijust s model), Kangertech and other companies. Regularity is better to choose, based on their own feelings. Proper operation and selection of a suitable filler lead to a longer service life of the device without the need for replacement. Regular (once a week) preventive measures also contribute to the timely update of the wick.

The whole process of replacing cotton wool on an electronic cigarette is shown in detail in the video: